-
1 maximum allowed power flow
Энергосистемы: максимально допустимый перетокУниверсальный англо-русский словарь > maximum allowed power flow
-
2 continuous current-carrying capacity
длительная пропускная способность по току
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.]Тематики
- электротехника, основные понятия
EN
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Англо-русский словарь нормативно-технической терминологии > continuous current-carrying capacity
-
3 ampacity (US)
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Англо-русский словарь нормативно-технической терминологии > ampacity (US)
-
4 continuous current
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
непрерывный ток
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999]Тематики
- электротехника, основные понятия
EN
Англо-русский словарь нормативно-технической терминологии > continuous current
-
5 current-carrying capacity
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
предельно допустимый ток
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.]Тематики
- электротехника, основные понятия
EN
прочность печатной платы к токовой нагрузке
Свойство печатной платы сохранять электрические и механические характеристики после воздействия максимально допустимой токовой нагрузки на печатный проводник или металлизированное отверстие печатной платы.
[ ГОСТ Р 53386-2009]Тематики
EN
Англо-русский словарь нормативно-технической терминологии > current-carrying capacity
-
6 level
1) уровеньб) ранг; позиция; категория; иерархическое положениев) амплитуда; интенсивность; относительное значениег) нивелир; ватерпас2) регулировать уровень; устанавливать уровень (напр. освещённости)3) приводить к одинаковому уровню; выравнивать; сглаживать; устранять отличия; нивелировать4) громкость || регулировать громкость5) ранжировать; определять позицию; относить к (определённой) категории; устанавливать степень субординации в иерархии6) горизонтальная линия или плоскость; ровная поверхность, плоская поверхность || устанавливать в горизонтальной плоскости; выравнивать; нивелировать; устанавливать по уровню или ватерпасу7) степень (напр. интеграции)10) рлк нацеливать; наводить; прицеливаться•- level of interactivity
- level within factor - acceptor level
- acceptor impurity level
- accuracy level
- activity level
- adaptation level
- algorithmic level
- allowed level
- allowed energy level
- alpha level
- alpha-geometric level
- alphamosaic level
- ambient level
- amplitude-modulation noise level
- atomic energy level
- audio-signal output level
- average picture level
- background level
- back-lobe level
- band-gap level
- band-power level
- band-pressure level
- base level
- behavioral level
- bit level
- black level
- blacker-than-black level
- blanking level
- brightness level
- bus interface level
- call-tone level
- carrier level
- carrier-noise level
- charged trapping level
- charge-storage level
- chorus level
- chromatic level
- circuit noise level
- clamp level
- clearance level
- clipping level
- common level
- compatibility level
- composite picture signal output level
- concentration level
- confidence level
- contamination level
- conventional significance level
- cross-product level - cutoff level
- data-flow level
- datagram level
- data service level
- deep level
- deep-lying level
- defect level - digital signal level
- discrete level
- discrete energy level
- donor level
- donor impurity level
- doping level
- DS level
- effective privilege level
- electric level
- electronic Zeeman level
- energy level
- entry level
- equivalent loudness level
- equivalent peak level
- exchange level
- exchange-split level
- excitation level
- exciton level
- extra level
- facsimile-signal level
- Fermi level
- Fermi characteristic energy level - floating level
- FM noise level
- foreground level
- free energy level
- function level
- functional level
- gate level
- gray level
- ground level
- ground state level
- HFS level
- high level
- higher bias level
- high logic level
- hum level
- hyperfine-structure level
- impedance level
- implementation level
- impurity level
- impurity energy level
- injection level
- input level - intensity level
- interchange level
- intermediate level
- intermediate energy level
- intrinsic level
- inversion level
- inverted level
- ISO 9660 implementation level
- ISO 9660 interchange level
- jet stream level
- jumbo cell level
- layout level
- light level
- line level
- local level
- logic level
- logical device level
- loudness level
- lower level
- lower energy level
- lowest level
- lowest energy level
- low-field level
- low logic level
- luminescent level
- mask level
- maximum record level
- maximum relative side-lobe level
- metastable level
- multiplet level
- neutral level
- noise level
- occupied energy level
- octave-band pressure level
- operate level of echo suppressor
- orbital energy level
- overload level
- partially filled level
- partially occupied level
- peak signal level
- peak sound-pressure level
- pedestal level
- perceived noise level
- perturbed level
- perturbed energy level
- phonon level
- power level
- power spectrum level
- precedence level
- pressure spectrum level
- price level
- printthrough level
- probability level
- program level
- pumping level
- quantization level
- quantizing level
- quasi-Fermi level
- recording level
- redundancy level
- reference level
- reference black level
- reference white level
- register transfer level
- relative co-polar side-lobe level
- relative cross-polar side-lobe level
- reorder level
- requested privilege level
- resistivity level
- resonance level
- risk level
- rotational level
- rotational energy level
- saturation level
- sensation level
- shallow impurity level
- side-lobe level
- signal level
- significance level
- singlet level
- soil level
- sound level
- sound-energy flux density level
- sound-power level
- sound-pressure level
- specific sound-energy flux level
- speech level
- strong-field level
- surface level
- switching level
- sync level
- synchronizing level
- system level
- television level
- testing level
- test's significance level
- threshold level
- through level
- timing level
- tolerable noise level
- transducer overload level
- transmission level
- trapping level
- trigger level
- triplet level
- true level
- turntable spirit level
- unaffected level
- unfilled level
- unfilled energy level
- unoccupied level
- unoccupied energy level
- upper level
- upper energy level
- usable levels
- vacant energy level
- vacuum level
- variable quantizing level
- variation level
- velocity level
- vibrational level
- vibrational energy level
- virtual level
- virtual energy level
- voltage level
- weighted noise level
- white level
- Zeeman energy level
- zero level -
7 level
1) уровеньб) ранг; позиция; категория; иерархическое положениев) амплитуда; интенсивность; относительное значениег) нивелир; ватерпас2) регулировать уровень; устанавливать уровень (напр. освещённости)3) приводить к одинаковому уровню; выравнивать; сглаживать; устранять отличия; нивелировать4) громкость || регулировать громкость5) ранжировать; определять позицию; относить к (определённой) категории; устанавливать степень субординации в иерархии6) горизонтальная линия или плоскость; ровная поверхность, плоская поверхность || устанавливать в горизонтальной плоскости; выравнивать; нивелировать; устанавливать по уровню или ватерпасу7) степень (напр. интеграции)10) рлк. нацеливать; наводить; прицеливаться•- acceptable reliability level
- acceptor impurity level
- acceptor level
- accuracy level
- activity level
- adaptation level
- algorithmic level
- allowed energy level
- allowed level
- alpha level
- alpha-geometric level
- alphamosaic level
- ambient level
- amplitude-modulation noise level
- atomic energy level
- audio-signal output level
- average picture level
- background level
- back-lobe level
- band-gap level
- band-power level
- band-pressure level
- base level
- behavioral level
- bit level
- black level
- blacker-than-black level
- blanking level
- brightness level
- bus interface level
- call-tone level
- carrier level
- carrier-noise level
- charged trapping level
- charge-storage level
- chorus level
- chromatic level
- circuit noise level
- clamp level
- clearance level
- clipping level
- common level
- compatibility level
- composite picture signal output level
- concentration level
- confidence level
- contamination level
- conventional significance level
- cross-product level
- C-scale sound level in decibels
- current privilege level
- cutoff level
- data service level
- data-flow level
- datagram level
- deep level
- deep-lying level
- defect level
- descriptor privilege level
- device level
- digital signal level
- discrete energy level
- discrete level
- donor impurity level
- donor level
- doping level
- DS level
- effective privilege level
- electric level
- electronic Zeeman level
- energy level
- entry level
- equivalent loudness level
- equivalent peak level
- exchange level
- exchange-split level
- excitation level
- exciton level
- extra level
- facsimile-signal level
- Fermi characteristic energy level
- Fermi level
- FIDO/opus/Seadog standard interface level
- filled energy level
- floating level
- FM noise level
- foreground level
- free energy level
- function level
- functional level
- gate level
- gray level
- ground level
- ground state level
- HFS level
- high level
- high logic level
- higher bias level
- hum level
- hyperfine-structure level
- impedance level
- implementation level
- impurity energy level
- impurity level
- injection level
- input level
- input/output privilege level
- integration level
- intensity level
- interchange level
- intermediate energy level
- intermediate level
- intrinsic level
- inversion level
- inverted level
- ISO 9660 implementation level
- ISO 9660 interchange level
- jet stream level
- jumbo cell level
- layout level
- level of details
- level of integration
- level of interactivity
- level within factor
- light level
- line level
- local level
- logic level
- logical device level
- loudness level
- low logic level
- lower energy level
- lower level
- lowest energy level
- lowest level
- low-field level
- luminescent level
- mask level
- maximum record level
- maximum relative side-lobe level
- metastable level
- multiplet level
- neutral level
- noise level
- occupied energy level
- octave-band pressure level
- operate level of echo suppressor
- orbital energy level
- overload level
- partially filled level
- partially occupied level
- peak signal level
- peak sound-pressure level
- pedestal level
- perceived noise level
- perturbed energy level
- perturbed level
- phonon level
- power level
- power spectrum level
- precedence level
- pressure spectrum level
- price level
- printthrough level
- probability level
- program level
- pumping level
- quantization level
- quantizing level
- quasi-Fermi level
- recording level
- redundancy level
- reference black level
- reference level
- reference white level
- register transfer level
- relative co-polar side-lobe level
- relative cross-polar side-lobe level
- reorder level
- requested privilege level
- resistivity level
- resonance level
- risk level
- rotational energy level
- rotational level
- saturation level
- sensation level
- shallow impurity level
- side-lobe level
- signal level
- significance level
- singlet level
- soil level
- sound level
- sound-energy flux density level
- sound-power level
- sound-pressure level
- specific sound-energy flux level
- speech level
- strong-field level
- surface level
- switching level
- sync level
- synchronizing level
- system level
- television level
- testing level
- test's significance level
- threshold level
- through level
- timing level
- tolerable noise level
- transducer overload level
- transmission level
- trapping level
- trigger level
- triplet level
- true level
- turntable spirit level
- unaffected level
- unfilled energy level
- unfilled level
- unoccupied energy level
- unoccupied level
- upper energy level
- upper level
- usable levels
- vacant energy level
- vacuum level
- variable quantizing level
- variation level
- velocity level
- vibrational energy level
- vibrational level
- virtual energy level
- virtual level
- voltage level
- weighted noise level
- white level
- Zeeman energy level
- zero levelThe New English-Russian Dictionary of Radio-electronics > level
См. также в других словарях:
Maximum throughput scheduling — is a procedure for scheduling data packets in a packet switched best effort communications network, typically a wireless network, in view to maximize the total throughput of the network, or the system spectral efficiency in a wireless network.… … Wikipedia
Power semiconductor device — Power semiconductor devices are semiconductor devices used as switches or rectifiers in power electronic circuits (switch mode power supplies for example). They are also called power devices or when used in integrated circuits, called power… … Wikipedia
Electric power transmission — Electric transmission redirects here. For vehicle transmissions, see diesel electric transmission. 400 kV high tension transmission lines near Madrid Electric power transmission or high voltage electric transmission is the bulk transfer of… … Wikipedia
Phantom power — (labeled as +48 V on some audio equipment) is a method that sends a DC electrical voltage through microphone cables. It is best known as a common power source for condenser microphones, though many active DI boxes also use it. Phantom power… … Wikipedia
War emergency power — (WEP) is an American term for the throttle setting on some World War II military aircraft engines. For use in emergency situations, it produced more than 100% of the engine s normal rated power for a limited amount of time, often about five… … Wikipedia
Intermittent power source — [ Erie Shores Wind Farm monthly output over a two year period] An intermittent power source is a source of electric power generation that may be uncontrollably variable or more intermittent than conventional power sources, and therefore non… … Wikipedia
magnetohydrodynamic power generator — ▪ physics Introduction any of a class of devices that generate electric power by means of the interaction of a moving fluid (usually an ionized gas or plasma) and a magnetic field. Magnetohydrodynamic (MHD) power plants offer the potential… … Universalium
National Maximum Speed Law — Double nickel redirects here. For the Interstate Highway in the central United States, see Double nickel (highway). 55 mph speed limit being erected in response to the National Maximum Speed Law. The National Maximum Speed Law (NMSL) in the… … Wikipedia
Economic Affairs — ▪ 2006 Introduction In 2005 rising U.S. deficits, tight monetary policies, and higher oil prices triggered by hurricane damage in the Gulf of Mexico were moderating influences on the world economy and on U.S. stock markets, but some other… … Universalium
electricity — /i lek tris i tee, ee lek /, n. 1. See electric charge. 2. See electric current. 3. the science dealing with electric charges and currents. 4. a state or feeling of excitement, anticipation, tension, etc. [1640 50; ELECTRIC + ITY] * * *… … Universalium
Rolls-Royce Merlin — Merlin The Rolls Royce Merlin … Wikipedia
